Search

Sealing Tie Holes

Sealing Tie Holes

Tie Holes a.k.a. Tie-Rod Holes in Concrete Structures

Introduction

Tie holes, also known as tie-rod holes, are small openings left in concrete structures after removing tie rods used in formwork. These holes can leak under hydrostatic pressure. An effective solution is polyurethane polymer foam injection.

In this article, we explore how a contractor effectively sealed tie holes and shrinkage cracks in water tanks for a rural water district. Utilizing the SealBoss Injection System, the team successfully resolved these challenges. This case study underscores the critical role of proper training and specialized equipment in preserving the integrity of concrete structures.

What are Tie Holes?

Tie holes are small openings in concrete structures that result from the removal of tie rods. Tie rods are essential components used in concrete formwork, which is the mold into which concrete is poured to achieve the desired shape. These rods help maintain the alignment and stability of the formwork during the concrete pouring and curing process.

Tie holes may start to leak under hydrostatic pressure caused by a source of water on the opposite side of the structure. 

Polyurethane Polymer Foam Injection is an effective method to seal leaking tie rods permanently.

Sealing Tie Holes and Cracks

A Case Study in Effective Water Tank Repair

In the world of construction, particularly in the construction of water tanks, shrinkage cracks and tie-holes are common issues that can lead to slowly weeping or even significant leaks. These problems are often accompanied by visible efflorescence, signaling a need for immediate and effective repair.

A recent project by a contractor in a rural water district expansion north of Atlanta, Georgia, perfectly illustrates how these challenges can be met with the right expertise and equipment.

Encountering the Challenge

During the construction of water tanks in this project, the contractor encountered both shrinkage cracks and tie-holes showing signs of leakage.

To address these issues effectively, the contractor sought on-site support and comprehensive systems training, specifically in the use of SealBoss 1510 NSF Hydrophobic Water Stop Foam and the P2002 High-Pressure Injection Pump.

The Training and Repair Process

The training began with a thorough inspection of the tank to identify the most actively leaking areas.

This was followed by a demonstration of the SealBoss Injection System application. The repair process involved a strategic approach to drilling holes:

The 1, 2, 3, 45 Degree Injection Method was used for the shrinkage cracks, and for sealing the tie-holes, a 45-degree hole was drilled 4 inches from the edge of each tie-hole until the steel insert was reached.

Preparation and Injection

Before the injection process, each drilled hole was pre-injected with water using a spray bottle. Given the ambient temperature of 38 degrees Fahrenheit, hot water (between 70 and 90 degrees Fahrenheit) was used for pre-injection to assist with the catalyzation time of the 1510 foam in the cold concrete. After flushing the holes, the installation of the SealBoss 13-100 AL Evolution Mechanical Packers commenced, followed by the injection process using the P2002 high-pressure injection pump.

Hands-On Learning and Independent Operation

The P2002 pump, known for its simplicity and drill-operated mechanism, was explained in detail. The training emphasized understanding injection pressure and the patience required for successful application.

Initially, the technician assisted with the pump operation, but within 10 minutes, the crew was able to inject independently.

Each packer was injected until there was positive refusal of material around each tie hole, and the same process was applied to the cracks.

Ensuring Long-Term Success

Once the crew gained confidence in operating the system, the focus shifted to cleaning and maintenance of the pump, ensuring its longevity and effectiveness for future projects.

Conclusion

This project north of Atlanta, Georgia serves as a prime example of how proper training and the right equipment can effectively address leaking tie holes and shrinkage cracks in new water tank construction.

The use of SealBoss 1510 NSF hydrophobic foam and the P2002 high-pressure injection pump, combined with hands-on training and a strategic approach to sealing, provided a durable solution to the problem of shrinkage cracks and tie-holes.

This case study not only highlights the importance of addressing these construction challenges promptly but also demonstrates the value of expert guidance and training in ensuring the longevity and integrity of water storage facilities.

Related Articles

Concrete Leak Sealing

Leak-Seal Foam Grout
Water Stop Foam Grout
Hydrophobic Injection Foam Grout

Our #1 Selling Polyurethane Injection Foam
Water Cut-Off Injection Grout
Semi-Flex Foam, Water-Activated chemical injection grout. Our most versatile product. Water activated hydrophobic polyurethane foam, expands up to 30-40 times.

Accelerator For 1510/1570 PU Injection Foam. Adjust foam gel-time and foam expansion from low foamer to high foamer depending application.

  • Light Weight, Modular Design
  • Electric Drill Operated
  • Single Piston System
  • 6000+ psi – 1 Component

ALUMINUM MECHANICAL PACKER

Dimensions
1/2″ X 4″
13 x 100mm

Standard Packer

Economical packer with removable anti-return valve in zerk permits port-port travel technique by removing the zerk fitting. Suitable for PU, EP, Polyacrylate, and Silicate grouts.

Bestseller – a SealBoss Standard

Contact Your SealBoss ® Technician
Popular​ Posts
More Posts
Archives
Categories
Scroll to Top