SealBoss 6060 QuickFix Road Repair
Road & Highway
Crack Mender
Spall Welder
SealBoss ® 6060 QuickFix - Pro
Quick Highway Spall & Pothole Repair in Minutes
- Heavy-Duty Formula
Does not deflect under loads, protects edges from spalling - Rapid Setting
Moderate traffic loads after fifteen (15) minutes, Full traffic after thirty (30) minutes. (70˚F/21˚C) - Extremely Wide Temperature Range
Use in coolers/freezers down to minus 20˚F (-29˚C), and temperatures up to 120˚F (49˚C)
With 6060 QuickFix you can repair concrete floor cracks and spalls to a level and even finish in minutes. SealBoss ® 6060 QuickFix is a new high tech two-part hybrid polyurethane for repairing and mending concrete. The very low viscosity allow for deep penetration into fine cracks, fissures and pores and the high strength but flexible properties of the product provide for a long lasting repair.
SealBoss ® 6060T QuickFix Advantages
- 100% Solids, VOC Free
- Produces High Strength Quickly
- Excellent Aggregate Bonding Properties
- Short ‘Return to Service’ Times
- Essentially Odorless
- Resistant to Petrochemicals
SealBoss ® 6060T QuickFix Applications
- Traffic Area Spall, Crack & Pothole Repairs
- Concrete and Asphalt ‘Welding’ Applications
- Grade Matching, Patching
- Highway, Bridge, Driveway, Walkway, Playground
- Warehouse, Ramp, Parking Decks, Garages
UNITS: 1GAL, 5 GAL, DRUMS, CARTRIDGES
SealBoss 6060 QuickFix - Pro Spall Repair in About 10 Minutes
Patch and Stitch Concrete Repair:
PATCH | SealBoss 6060 can be used to repair damaged and uneven concrete surfaces.
STITCH | The product penetrates deep into cracks and fissures mending them back together.
With 6060 QuickFix you can repair concrete floor cracks and spalls to a level and even finish in minutes. SealBoss 6060 QuickFix is a new high tech two-part hybrid polyurethane for repairing and mending concrete. The very low viscosity allow for deep penetration into fine cracks, fissures and pores and the high strength but flexible properties of the product provide for a long lasting repair. SealBoss offers a complete floor repair and road surface spot and pothole repair solution. Products are supplied in bulk and in cartridges systems.
Product Description
SealBoss ® 6060 T QuickFix has been formulated for highway and other extensive repair projects where a fast cure and permanent solution is needed. Depending on the requirements, SealBoss ® 6060 T QuickFix can be used with a variety of aggregates including gravels and sands thereby allowing the user to solve several problems with one material.
Based on the product’s rapid cure properties, repairs can be completed with minimal traffic closure time.
SealBoss ® 6060 T QuickFix has excellent chemical resistance to oils, hydraulic fluids, gasoline, salts, and antifreeze. The product contains no solvents and has no odor.
SealBoss ® 6060 T QuickFix is a fast cure, low viscosity, rapid set, high strength, self-leveling, two component, 1:1 ratio by volume, 100% solids polyurethane polymer for concrete and asphalt repairs.
SealBoss ® 6060 T QuickFix works for concrete and asphalt repairs and is an excellent high strength bonding agent for use with a wide variety of aggregates. The product penetrates into small cracks and forms a high strength adhesive bond between broken structures with the benefit of sealing the base against further erosion from water in outside applications. The tack free time is 5 to over 10 minutes depending on temperature.
Ask your SealBoss ® technician for details. The product is for professional use.
Installation Guidelines
Clean the area of debris and contaminants, such as oils, loose materials, dirt, rubber etc., to allow for good adhesion of the product. Expose clean rough concrete for best results. If using a saw to cut concrete and clean the crack, remove all the dust from the cutout area. Make sure the surfaces are dry. All equipment, pumps and hoses must be dry. Avoid moisture contact with the mixture.
For bulk mixing, pre‑mix each component thoroughly. Proportion equal parts by volume of Component “A” and Component “B” through appropriate metered mixing equipment. Mix only the quantity that can be used within pot life and do not allow mixed material to reside in static mixing head or mixer for more than 1 minute or nozzle blockage may result. Do not add solvents. Minimum age of concrete must be 21‑28 days, depending on curing and drying conditions prior to applications.
Deep Crack / Joint Application
Apply product to the bottom of the crack and work up in layers. First apply product, then deliver aggregate into the applied product. Add more product & aggregate. Repeat the steps until reaching the finished grade.
Aggregate
The use of approved non reactive aggregate with SealBoss ® 6060 T QuickFix may increase gel and cure times. Aggregate must be free of moisture. Dry silica sand and a variety of gravel grades may be used depending on the applications and specific demands of the job site.
