Search

SealBoss 6060 Quick Fix Floor Repair

Concrete Spall & Floor Crack Repair Mender for Concrete

Heavy-Duty Repair Polymer for Class 6, 7, 8 & 9 Industrial Floors, Floor Repair

SealBoss 6060 QuickFix Concrete Spall & Crack Repair Mender for Concrete

SealBoss  6060 QuickFix Properties:

  • Heavy-Duty Formula
    Does not deflect under loads, protects edges from spalling
  • Rapid Setting
    Moderate traffic loads after fifteen (15) minutes, Full traffic after thirty (30) minutes. (70˚F/21˚C)
  • Extremely Wide Temperature Range
    Use in coolers/freezers down to minus 20˚F (-29˚C), and temperatures up to 120˚F (49˚C)

SealBoss  6060 QuickFix Advantages:

  • 100% Solids, VOC Free, Low Emitting Sealant
  • Produces High Strength Quickly
  • Excellent Aggregate Bonding Properties
  • Short ‘Return to Service’ Times
  • Essentially Odorless, Resistant to Petrochemicals
  • Grade Matching, Patching, Fill & Repair before Coating
  • Interior and Exterior use
SEALBOS-6060-POLYUREA-ROAD-REPAIR

10 Minute Crack and Spall Repair​

Patch and Stitch Concrete Repair:

PATCH  |  SealBoss 6060 can be used to repair damaged and uneven concrete surfaces.
STITCH  |  The product penetrates deep into cracks and fissures mending them back together.

Professional grade formula for for industrial, commercial and residential concrete floors.

SealBoss 6060 QuickFix - Pro Spall Repair in About 10 Minutes

With 6060 QuickFix  you can repair concrete floor cracks and spalls to a level and even finish in minutes. SealBoss  6060 QuickFix  is a new high tech two-part hybrid polyurethane for repairing and mending concrete. The very low viscosity allow for deep penetration into fine cracks, fissures and pores and the high strength but flexible properties of the product provide for a long lasting repair. SealBoss offers a complete floor repair and road surface spot and pothole repair solution. Products are supplied in bulk and in cartridges systems.

SEALBOSS FLOOR REPAIR - ROAD REPAIRProduct Description

SealBoss ® 6060 QuickFix Pro Spall Repair is an advanced polyurethane formulated, low viscosity, rapid set, high strength, ultra low viscosity, self leveling, two component, 1:1 ratio by volume, 100% solids repair material. This strong and rigid material has been designed to fix spalled concrete surfaces and cracks, and to rebuild damaged control joints effectively and quickly. SealBoss ® 6060 QuickFix works for concrete and asphalt repairs.

The product penetrates into small cracks and forms a high strength adhesive bond between broken structures with the benefit of sealing the base against further erosion from water in outside applications. The tack free time is 5 to over 15 minutes depending on temperature.

Ask your SealBoss ® technician for details. The product is for professional use.

Installation Guidelines

Clean the area of debris and contaminants, such as oils, loose materials, dirt, rubber etc., to allow for good adhesion of the product. Expose clean rough concrete for best results. If using a saw to cut concrete and clean the crack, remove all the dust from the cut out area. Make sure the area is dry. All equipment, pumps and hoses must be dry. Avoid moisture contact with the mixture.

For bulk mixing, pre‑mix each component thoroughly. Proportion equal parts by volume of Component “A” and Component “B” through appropriate metered mixing equipment. Mix only the quantity that can be used within pot life and do not allow mixed material to reside in static mixing head or mixer for more than 1 minute or nozzle blockage may result. Do not add solvents. Minimum age of concrete must be 21‑28 days, depending on curing and drying conditions prior to applications.

Deep Crack / Joint Application
Apply product to the bottom of the crack and work up in layers. First apply product, then deliver aggregate into the applied product. Add more product & aggregate. Repeat the steps until reaching the finished grade.

Aggregate

The use of approved non reactive aggregate with SealBoss ® 6060 QuickFix will increase gel and cure times.
Aggregate must be free of moisture. In exterior applications, the use of dry silica sand (grit sizes from 12 to 60) will reduce discoloration from UV Rays. Certain gravel grades may be used on large applications. Ask your SealBoss technician for details.

Scroll to Top